| Product Condition | New original or used original. Please confirm the condition with us before ordering. |
| Shipping Information | Worldwide shipping via DHL, FedEx, and UPS. 3-5 working days to most destinations. Secure export packaging for the cable harness. |
| Buyer Benefits |
|
| Item Location | Ships from Shanghai, China. Lead time confirmed with your inquiry. |
| Payment Information | PayPal, T/T, and Alibaba Trade Assurance accepted. Send your inquiry for a quotation. |
12,000+ parts in stock,Tested before shipping,Reply within 24 hours
InquiryThe ABB 3HAC14139-1 is the manipulator harness for axis 5 — the wrist section of the wiring — on IRB 6650S and IRB 6660 manipulators. ABB lists it in its spare part catalogue as "Manipulator harness ax 5", and in the IRB 6650S product manual it is the harness fitted inside the upper arm tube, running out to the axis 5 motor at connectors R4.FB5 and R4.MP5. It is supplied as a complete pre-manufactured assembly with the factory connectors fitted. Send us the robot serial number and the article number on the harness label, and we confirm the match before you order.
| Part number | 3HAC14139-1 |
| Manufacturer | ABB (original spare part) |
| ABB catalogue name | Manipulator harness ax 5 |
| Type | Manipulator harness, axis 5 — the wrist cabling section running inside the upper arm tube to the axis 5 motor, supplied as one complete assembly |
| Compatibility | ABB IRB 6650S and IRB 6660 manipulators, as listed in the IRB 6650S circuit diagram. Send us your robot serial number and the article number on the harness label, and we confirm the match before you order. |
| Axis | Axis 5 (wrist) |
| Connection points | Motor axis 5 with connectors R4.FB5 and R4.MP5 |
| Net weight | 0.54 kg |
| Gross weight | 0.54 kg |
| Customs HS code | 85444290 |
| Minimum order quantity | 1 piece |
| Country of origin | Czech Republic (CZ) |
| Condition | New original or used original. Please confirm the condition with us before ordering. |
Send the robot serial number and the article number printed on the harness label, and we confirm the match before you order.
This harness provides the wired path for the axis 5 motor, encoder and brake along the manipulator to the controller. It sits inside the upper arm tube, so it has to follow the arm through every permitted motion while carrying feedback and motor power for the wrist — and the wrist is where the arm bends through its largest angle at the highest frequency. That is why this section is the one that usually reaches the end of its flexing life first.
Because the harness is matched to the robot model and arm configuration, a visually similar harness is not automatically interchangeable: branch layout, connectors, shielding, clamp points and the moving-route geometry all have to match what is installed. The reliable route is the label on the harness you are replacing and the serial number of the robot it came from — send us both and we match them against the ABB spare part data before you order.
Before removal: switch off all electric power to the robot and apply lockout and tagout before accessing the wrist cabling, following the ABB maintenance safety procedure. Photograph and label every connector and its routing before you take the harness out, and keep the replacement clear of sharp edges and heat sources. Inspect the new harness for abrasion, kinks, crushed sections and a cracked jacket before fitting it, and route it with the original cable clamps so signal and power cables stay separated and the bend radius is preserved. After fitting, jog axis 5 through its travel while watching the feedback, then complete the reference and calibration checks per the ABB procedure before the robot returns to production.
Request a quote: Send your robot serial number and the article number on the harness label (3HAC14139-1). We confirm condition, fitment and lead time, then send a quotation — before you place any order.
If you have any suggestions, please contact us
Contact Us