ENEN

All Categorys

ABB Robot Parts
KUKA Robot Parts
FANUC Robot Parts
YASKAWA Robot Parts

All Small Categorys

ABB Robot Parts
KUKA Robot Parts
FANUC Robot Parts
YASKAWA Robot Parts
ABB JC2000-0137 Hall Effect Joystick for Teach Pendants
ABB JC2000-0137 Hall Effect Joystick for Teach Pendants
ABB JC2000-0137 Hall Effect Joystick for Teach Pendants
ABB JC2000-0137 Hall Effect Joystick for Teach Pendants

ABB JC2000-0137 Hall Effect Joystick for Teach Pendants

Product Condition New original or used original. Please confirm the condition with us before ordering.
Shipping Ships from Shanghai, China. Delivery lead time: 3-5 working days after order confirmation. Worldwide delivery by DHL / FedEx / UPS with secure packaging.
Buyer Benefits
  • Joystick from the JC2000 series, the contactless Hall effect joystick family built by Penny & Giles (Curtiss-Wright) and used in ABB teach pendant units.
  • Contactless sensing: no wiper or track to wear out, which is why this series was selected for robot teach units.
  • Restores accurate jogging without replacing the whole teach pendant — the joystick is a separate replaceable item.
  • Tell us your pendant article number before ordering: JC2000 variants differ, and the fit is confirmed before we supply.
  • Runs a joystick calibration after fitting, following the procedure for your pendant generation.
  • Supplied as new original or used original; we confirm the condition with you before you order.
  • Request a quote for current pricing and lead time — we do not publish stock levels or fixed dispatch promises.
  • Shipped worldwide from Shanghai, China with protective packaging via DHL / FedEx / UPS.
Item Location Ships from Shanghai, China.
Payment PayPal / T/T / Alibaba Trade Assurance.
Inquiry Contact Us
  • Description
Can’t Find Your Part?

12,000+ parts in stock，Tested before shipping，Reply within 24 hours

+86-18616903058
[email protected]
Inquiry

Hall Effect Joystick for ABB Teach Pendants

Specifications

Category Joystick controller (teach pendant spare part)
Brand ABB (robot system). The JC2000 series joystick is built by Penny & Giles, now part of Curtiss-Wright.
Product Name Joystick / joystick controller
Part Number JC2000-0137
Product Series JC2000
Definition JC2000-0137 is a joystick from the JC2000 series, the contactless Hall effect joystick family used as the jogging control in ABB teach pendant units.
Function Converts the operator's hand movement into proportional signals, so the robot axes can be jogged from the teach pendant during programming, setup and fault recovery.
Technology Contactless Hall effect sensing. The JC2000 is built as a multi-axis contactless controller with no wiper or track to wear, which is why the series was taken into robot teach units.
Series / Compatibility The JC2000 series was selected by ABB for its IRC teach units and is used in the IRC5 generation. Which pendant this specific order code fits is not stated in publicly available documentation — please send us your pendant article number and we will confirm the match before supply.
Electrical / Mechanical Data Not published for this order code. The JC2000 series is documented in the manufacturer's datasheet, but those figures belong to the series and not to every variant, so we do not transfer them to JC2000-0137. Ask us for the specification you need and we will confirm it directly.
Condition New original or used original. Please confirm the condition with us before ordering.
Detailed Technical Parameters Information not officially documented for this variant. Please provide your teach pendant article number, or a photo of the joystick you are replacing, and we will confirm the match before supply.

Industrial Applications

  • Replacing a worn or drifting joystick in an ABB teach pendant, so manual jogging is accurate again.
  • Repairing a pendant after a drop or impact that has damaged the lever or the sensing unit.
  • Commissioning and changeover work, where the joystick is the operator's main control for jogging and fine positioning.
  • Maintenance and fault recovery on ABB robot cells in automotive, metal processing, material handling, electronics and general automation.
  • Spares provisioning for service teams, since the joystick is one of the most heavily used parts on a pendant.

Design Purpose

  • Act as the primary motion input of the teach pendant, giving proportional control over robot movement.
  • Use contactless Hall effect sensing so there is no mechanical wear path, unlike a potentiometer joystick.
  • Deliver smooth, repeatable low-force fingertip control for precise manual positioning.
  • Survive continuous daily use on the shop floor, and be replaceable on its own so the whole pendant does not have to be scrapped.
Safety & Installation Notice
  • Stop the robot, switch to manual mode and isolate the controller before opening the pendant or disconnecting the pendant connector.
  • The joystick is part of a pendant that also carries the emergency stop and the enabling device. After any work inside the pendant, verify those safety functions before the cell goes back into production.
  • Confirm the variant before ordering. JC2000 codes differ in configuration, and the pendant this code fits is not documented in public sources — quote us your pendant article number.
  • Do not force the lever or the handle. The sensing unit is not designed to take side loads or a pressed-in stem.
  • Take electrostatic precautions when the pendant is open, and keep the connector and ribbon cable free of dust, oil and metal swarf.
  • Refit the rubber boot correctly: a torn or mis-seated boot lets contamination reach the sensing area and shortens service life.
  • After fitting, run the joystick calibration routine for your pendant generation and check the centre position before returning to production.

Common Failure Modes

  • Joystick drift — the robot creeps without the lever being touched, so the lever is no longer returning to a clean centre.
  • Dead or unresponsive direction — moving the lever one way produces no motion.
  • Intermittent response — motion cuts in and out, often from a failing connection, a damaged cable or contamination.
  • Broken or bent lever after a drop, or a stem pushed in so the joystick no longer tracks properly.
  • Torn or displaced rubber boot, letting dust and oil reach the sensing area.
  • Ordering the wrong JC2000 variant, because the series covers several configurations and the pendant fit is not published for this code.
  • Skipping the joystick calibration after fitting, so the pendant keeps the old centre values.

Why Choose Us

  • Identity backed by the manufacturer: the JC2000 series is the contactless Hall effect joystick built by Penny & Giles (Curtiss-Wright) and taken into ABB teach units.
  • We confirm the match by your pendant article number before quoting, instead of selling a joystick on a guessed description.
  • We do not copy series datasheet figures onto a specific order code — we confirm the specification you need directly.
  • Technical support for joystick calibration, installation and drift diagnosis.
  • New original or used original; we confirm the condition with you before you order.
  • Carefully packed and shipped worldwide from Shanghai, China via DHL / FedEx / UPS.

Related Products

  • JC2000-0049 — another joystick assembly from the JC2000 series, listed for ABB IRC5 FlexPendant units. A different code with a different configuration; confirm which one your pendant uses.
  • 3HAC028357-001 — ABB DSQC679 FlexPendant for IRC5 controllers. The joystick is a replaceable item inside the pendant; confirm the joystick variant by pendant article number.
  • 3HAC085590-001 — ABB FlexPendant DSQC3120A, a later pendant generation. A different pendant; confirm compatibility separately.

Send us your pendant article number and we will quote this joystick together with the touchscreen, keypad, housing parts or cable your pendant needs.

Online Inquiry

If you have any suggestions, please contact us

Contact Us
IT'S SUPPORTED BY

Copyright © SongWei Robotics All Rights Reserved  -  Privacy Policy