| Product Condition | New original or used original. Please confirm the condition with us before ordering. |
| Shipping Information | Ships from Shanghai, China. Delivery lead time: 3-5 working days after order confirmation. Worldwide delivery by DHL / FedEx / UPS, with both connector faces protected so the cable arrives ready to fit. |
| Buyer Benefits |
|
| Item Location | Ships from Shanghai, China. |
| Payment Information | PayPal / T/T / Alibaba Trade Assurance. |
12,000+ parts in stock,Tested before shipping,Reply within 24 hours
InquiryJZSP-CVP02-10E is the YASKAWA 10 m encoder feedback cable for Sigma-series servo motors and drives. Yaskawa parts lists also write the number as JZSP-CVP02-10-E; both forms refer to this same cable. It carries the encoder signal from the servo motor back to the drive, with a right-angle metal circular plug at the motor end and a rectangular plug at the drive end. The -10- in the number is the length: the same CVP02 family also comes in 8 m, 15 m, 20 m and 25 m versions, so the suffix decides which cable fits your installation. Send us the number on the cable label, the servo motor and drive models, or a photo of both connectors, and we confirm the match before you order.
| Part Number | JZSP-CVP02-10E |
| Alternate Number Form | JZSP-CVP02-10-E, the same cable written with a hyphen before the E in Yaskawa parts lists and most reseller listings. Both forms are kept on this page so either number finds the right part. |
| Product Name | Encoder feedback cable / incremental encoder cable for YASKAWA Sigma-series servo systems |
| Cable Length | 10 m. The -10- in the article number is the length designation. |
| Length Variants | JZSP-CVP02-08-E (8 m), JZSP-CVP02-15-E (15 m), JZSP-CVP02-20-E (20 m) and JZSP-CVP02-25-E (25 m) are other lengths in the same CVP02 family. Each is a different part from this 10 m cable. |
| Other Cable Families | JZSP-CVP01, JZSP-CVP11, JZSP-CVP12 and JZSP-CMP60 are other YASKAWA encoder or servo cables with different connector configurations. Each is a different part from this one. |
| Function | Transmits the encoder feedback signal from the servo motor to the drive for closed-loop position and speed control, and shields that signal from electrical noise along the run. |
| Construction | The product photo shows a coiled black cable with a pale rectangular plastic plug and visible metal contacts at one end, and a silver 90-degree right-angle circular metal plug with a knurled locking ring and a black pin face at the other. No part number is legible in the photo; send us a photo of the label on your fitted cable. |
| Identification & Setup | Switch off the drive before connecting or disconnecting the cable, check both plug faces for bent pins and seat the knurled locking ring fully, then power up and confirm encoder communication at the drive. On a robot axis, follow the YASKAWA home position calibration procedure after the exchange. Send us the servo motor model, the drive model and the controller manufacturing number and we confirm the procedure for your system. |
| Condition | New original or used original. Please confirm the condition with us before ordering. |
Two numbers cause most of the mix-ups here: JZSP-CVP02-10E and JZSP-CVP02-10-E are the same 10 m cable, while a different number in the -xx-E position means a different length. Send us the number on the cable label, the servo motor and drive models, and a photo of both connectors, and we confirm the version before we quote.
Request a quote for current pricing and lead time – send us the number on the cable label (JZSP-CVP02-10E or JZSP-CVP02-10-E), the servo motor and drive models, and a photo of both connectors, and we confirm the length suffix before you order.
If you have any suggestions, please contact us
Contact Us