YASKAWA JZSP-CMP60-10-E Encoder Cable 10 m for SGMCS Servo Motors

YASKAWA JZSP-CMP60-10-E Encoder Cable 10 m for SGMCS Servo Motors

JZSP-CMP60-10-E is the YASKAWA 10 m encoder cable with connectors for SGMCS servo motors, used to carry the feedback signal between the motor and the SERVOPACK. In the YASKAWA SGMCS catalogue it sits in the encoder cable table as the 10 m entry of the standard JZSP-CMP60 series: a cable that arrives with both ends fitted, the SERVOPACK end using a Molex plug connector and the encoder end a crimped 10-pin straight plug. The same length is also available as the flexible JZSP-CSP60-10-E, which YASKAWA specifies for movable sections such as robot arms — the standard and flexible types are not interchangeable in the same installation. Send us the part number on your original cable and the model on your drive and motor, and we confirm the match before you order.

Specifications

Packing dimensions and origin are stated against the article number we quote. Send us the part number on your original cable and the model on your drive and motor, and we confirm the match before you quote.

Industrial Applications

• SGMCS direct drive servo motor installations — the encoder cable that closes the position loop between the motor and the amplifier.
• Robot and machine tool axes on the YASKAWA servo platform, where the feedback run is long enough to need a pre-terminated 10 m cable instead of a made-up one.
• Retrofit and repair of ageing drives, where a damaged encoder cable shows up as intermittent position errors that come and go with the axis movement.
• Cells with a long distance between the drive cabinet and the motor, where a standard 10 m run avoids putting a joint on the cable run.
• Service stock for lines where the encoder cable is the wear item rather than the motor or the drive.

Design Purpose

• Carry the encoder feedback between motor and SERVOPACK with both ends already fitted, so the cable can be installed without a crimping tool or a soldering bench.
• Use shielded construction with a dedicated FG shield wire, so the position signal is not degraded by the motor and drive cables running alongside it.
• Give the installer the same wiring on every length in the series, so a shorter or longer replacement follows the same pin assignment.
• Offer a standard and a flexible variant of the same length, so a cell that puts the cable in a moving section can be specified for flexing and a fixed installation can stay on the standard type.
• Meet the UL20276 cable standard at a 80 °C rated temperature, which is what lets it sit inside the drive cabinet next to the amplifier.

Common Failure Modes

• Intermittent position errors or a position deviation alarm that comes and goes — a classic sign of a cable whose shield or connector has degraded rather than a failed encoder.
• Errors that only appear when the axis moves to a particular angle — that points at a broken conductor inside the insulation, which is where flexing and vibration do their damage.
• Noise on the feedback signal after a new installation — usually the shield wire was not connected to the connector case at one end.
• A cable that was routed through a moving section and has been flexed into failure — that installation needs the flexible JZSP-CSP60 variant, not this standard type.
• Visible damage at the connector, a cracked shell or a connector that no longer latches, after a knock or a pull on the cable.
• Faults that follow a replacement but do not go away — check the shield grounding and the pin assignment before ordering another cable, because the standard and flexible series use different wire colours.

Why Choose Us

• Genuine YASKAWA part, supplied against part number JZSP-CMP60-10-E.
• We confirm the part number, the standard or flexible type and the drive and motor models before dispatch, so the cable you receive fits the axis it goes back on.
• New original or used original available — the condition is confirmed with you before you order.
• Photos of the actual cable, including the connectors at both ends, provided on request.
• Support with part-number identification across the JZSP-CMP60 and JZSP-CSP60 length series and the loose-wire and connector-kit variants, so the right form factor is ordered the first time.
• Packed for export with the connectors protected in transit; ships worldwide from Shanghai.

Related Products

• SGD7S-1R6A00A — YASKAWA Sigma-7 servo amplifier, the drive that this encoder cable feeds. A different part number, and the servo side of the same signal path.
• UTTAH-B17TL — YASKAWA absolute rotary encoder. The sensing element at the far end of this cable; a different part number and a different function.
• HB1371456-1 — YASKAWA robot connector cable. A different cable for a different connection; not a substitute for this encoder cable.
• USB-JZSP-CMS02 — YASKAWA programming cable. A different cable for a different purpose, not an encoder cable.
• Yaskawa Cables & Dress Packages — the rest of the YASKAWA cable and dress package range.

Request a quote for current pricing and lead time – send us the part number on your original cable and the model on your drive and motor, and we confirm the match before you order.